nano ультразвуковые датчики

Sensorbild - Matrix

Обзор

Название говорит само за себя. Всего 55 мм длинной, включая разъем, датчик nano является самым коротким существующим М12 ультразвуковым датчиком.

СКАЧАТЬ СЕМЕЙСТВО ДАТЧИКОВ В PDF ФАЙЛ

Основные характеристики

  • Ultrasonic sensor in the M12 threaded sleeve
  • The total length including plug is only 55 mm
  • IO-Link interface для поддержки нового стандарта в промышленности
  • Improved temperature compensation adjustment to working conditions within 45 seconds
  • UL Listed to Canadian and US safety standards

Basics

  • 1 дискретный выход Push-Pull pnp/npn типа
  • Analogue output 4–20 mA or 0–10 V
  • 2 detection ranges with a measurement range of 20 mm to 350 mm
  • microsonic Teach-in on pin 2
  • 0.069 mm resolution
  • Operating voltage 10–30 V for use with various voltage networks

Описание

With a housing length of only 55 mm

nano sensors with switching outputs are the smallest ultrasonic sensors inside the M12 threaded sleeve on the market. Analogue sensors are 60 mm long. The nano has a 4-pole M12 circular plug and are taught via pin 2.

For the nano sensor family

there are 2 output stages and 2 measuring ranges available:  

1 дискретный выход Push-Pull (pnp/npn типа) and IO-Link-Interface
1 analogue output 4–20 mA or 0–10 V

The temperature compensation

of the sensors profits from a significant improvement. The sensors reach their operating point only 45 seconds after activation of the operating voltage. We now compensate for the influence of self-heating and installation conditions. This brings improved precision shortly after activation of the supply voltage and in running operation.

The nano sensors with switched output have three operating modes:

New! With the internal alignment assistance

the sensors with Push-Pull switching output can be optimally aligned to the object during installation.

nano sensor using alignment assistance
  • Single switching point
  • Two-way reflective barrier
  • Window mode

Teach-in of a single switching point

  • Place object (1) to be detected at the desired distance
  • Apply +UB to pin 2 for about 3 seconds
  • Then apply +UB to pin 2 again for about 1 second

Teach-in of a switching point

Teach-in of a two-way reflective barrier

with a fixed mounted reflector.

  • Apply +UB to pin 2 for about 3 seconds
  • Then apply +UB to pin 2 again for about 10 second

Teach-in of a two-way reflective barrier

To set a window with two switching points

  • Place object to the sensor-close window limit (1)
  • Apply +UB to pin 2 for about 3 seconds until both LEDs flash
  • Then move the object to the sensor-distant window limit (2)
  • Then apply +UB to pin 2 again for about 1 second until LED2 extinguishes

For setting an analogue output

  • initially position the object to be detected on the sensor-close window limit (1)
  • Apply +UB to pin 2 for about 3 seconds until both LEDs flash
  • Move the object to the sensor-distant window limit (2)
  • Then apply +UB to pin 2 again for about 1 second

Teach-in of an analogue characteristic or of a window with two switching points

NCC/NOC

and rising/falling analoge characteristic can also be set via pin 2.

One green and one yellow LED

indicate the state of the output and support microsonic Teach-in.

Интерфейс IO-Link

в версии 1.1.2 поддерживается датчиками дискретный выход Push-Pull . Ультразвуковые датчики nano оборудованы Smart Sensor Profile, который обеспечивает большую транспарентность между устройствами IO-Link.

Top